How do I use my Spirit?

Want to learn more about the correct way get bubbling with your Spirit? Check out the below guide, How To video, and user manual.

 

Follow the steps below to get bubbling with your Spirit:

  1. Begin by filling your cabonating bottle with cold water up to the fill line. Do not add anything to the bottle besides water before carbonating.
  2. Pull the bottle rest towards you until a click sound is heard.
  3. Insert the carbonating bottle into the Snap-Lock by pushing the bottle up and back. The Snap-Lock will hold the bottle in a vertical position suspended above the base.
  4. Push down firmly on the carbonating button for around 2 seconds, release, and repeate -- 3 times for light fizz, 5 times for strong fizz, and more for extra strong fizz.
  5. When you've reached the right carbonation level, gently pull the bottle towards you until it reaches its fully forward position and remove.
  6. Enjoy your bubbles!

Click here to see the Spirit user manual.

Questions? Contact us via email or phone at 0800-085-8373,

How do I install the cylinder on my Spirit?

Need help installing your cylinder? Check out the guide below for instructions.

*Please note that the 130L cylinder (discontinued) is not compatible with your Sparkling Water Maker.

Follow the steps below to install your new cylinder:

  1. Place the cylinder on a flat sturdy surface in an upright position and remove the seal and cap by twisting it counter-clockwise. Make sure to remove the carbonating bottle if it is installed in the Sparkling Water Maker.
  2. With the Sparkling Water Maker in an upright position on a flat, sturdy surface, remove the back cover by pressing on the top and pulling it away from the body of the Sparkling Water Maker.
  3. Set the back cover aside.
  4. Gently tip the Sparkling Water Maker forward and insert the cylinder into the back. First insert the base of the cylinder followed by the body and then tilt it towards your Sparkling Water Maker.
  5. Screw the cylinder counter-clockwise while applying gentle pressure until it is firmly held in place. Do not use tools and make sure the cylinder is secured in its place.
  6. Reinstall the back cover by fitting the upright tab at the bottom into the rear slot at the base of the Sparkling Water Maker. Then push the cover into place onto the back of the Sparkling Water Maker.
  7. Enjoy your bubbles!

Questions? Contact us via email or phone at 0800-085-8373.

How can I tell if my Spirit is out of gas?

Not sure if your CO2 cylinder is empty?

  • Make sure the cylinder is tight enough and retighten if necessary by twisting it to the right.
  • If you're still not getting enough bubbles and if you don't hear a sputtering sound when you press the carbonating button, you may be out of gas. You can get a new cylinder through our online exchange program or a participating retail location.

Still not sure if your carbonating cylinder is out of gas? Check out the guide below.

Questions? Contact us via email or phone at 0800-085-8373,
How can I be sure the bottle on my Spirit is in the right position?

It's easy! Once inserted properly, the Snap-Lock will catch the carbonating bottle and hold it in a vertical position suspended above the base.

Check out the guide below for more information.

Questions? Feel free to contact us via email or phone at 0800-085-8373,

How do I clean my Spirit?

Taking care of your Sparkling Water Maker is super easy! You can use a mild liquid dish soap and a soft damp cloth to gently clean your Fizzi Sparkling Water Maker.

Do not use abrasive cleaners or sharp tools to clean.

Check out the guide below for more cleaning and handling instructions.

Questions? Contact us via email or phone at 0800-085-8373,
How do I replace my Spirit gas cylinder?

Out of bubbles? Check out the guide below for help replacing your cylinder.

Follow the steps below to replace your empty carbonating cylinder:

  1. Place the cylinder on a flat sturdy surface in an upright position and remove the seal and cap by twisting it counter-clockwise. Make sure to remove the carbonating bottle if it is installed in the Sparkling Water Maker.
  2. With the Sparkling Water Maker in an upright position on a flat, sturdy surface, remove the back cover by pressing on the top and pulling it away from the body of the Sparkling Water Maker.
  3. Set the back cover aside.
  4. Gently tip the Sparkling Water Maker forward and unscrew the empty CO2 cylinder by twisting it clockwise. Do not use tools.
  5. Place your empty cylinder aside and take out your replacement cylinder.
  6. With the Sparkling Water Maker tipped forward, insert the new cylinder into the back. First insert the base of the cylinder followed by the body and then tilt it towards your Sparkling Water Maker.
  7. Screw the cylinder counter-clockwise while applying gentle pressure until it is firmly held in place. Make sure the cylinder is secured in its place.
  8. Reinstall the back cover by fitting the upright tab at the bottom into the rear slot at the base of the Sparkling Water Maker. Then push the cover into place onto the back of the Sparkling Water Maker.
  9. Save your empty cylinder so you can swap it for a gas refill.
  10. Enjoy your bubbles!
Questions? Contact us via email or phone at 0800-085-8373.
How do I add flavour to sparkling water I made using my Spirit?

Want to elevate your sparkle? Check out the guide below to learn how to use our sparkling drink mixes.

Remember

Always fizz water before adding flavour.

 

The guide above contains instructions for adding flavour:

Sparkle a bottle of fresh, cold water with your Sparkling Water Maker and select your favourite sparkling drink mix. We offer Classic syrups, Diet syrups, Fruit Drops, Organic Soda Press, and Fruits syrups.

To add sparkling drink syrups:
  • Use the indicated lines on the cap of the flavour bottle to choose a regular or light sweetness level.
  • Tilt the carbonating bottle at an angle and pour the flavour into your sparkling water.
  • Close the bottle with the fizz-preserving cap and shake gently to mix.
  • Enjoy your bubbles!

To add Soda Press sparkling drink mixes:

  1. Add 2 tbsp (30 mL) of the Soda Press syrup to about a 2/3 cup (170 mL) of sparkling water. You can adjust the amount of syrup you add according to your taste.
  2. Enjoy your bubbles!

To add Fruit Drops:

  1. Take approximately half a teaspoon of your chosen flavour to use with one liter of sparkling or still water.
  2. Tilt the carbonating bottle at an angle and add the fruit drops.
  3. Enjoy your bubbles!
Questions? Contact us via email or phone at 0800-085-8373.
How to use video: How do I use my Spirit?

Need assistance in learning how to use your Sparkling Water Maker? Take a look at this video and I am sure you will be up and sparkling right away!

Questions? Contact us via email or phone at 0800-085-8373,

How do I carbonate water with my Spirit?

Let's get you bubbling! Check out the guide below to begin.

It's easy to get sparkling with your Spirit Sparkling Water Maker:

  1. Begin by filling your carbonating bottle with cold water up to the fill line. Do not add anything to the bottle besides water before carbonating.
  2. Pull the bottle rest towards you until a click sound is heard.
  3. Insert the carbonating bottle into the Snap-Lock by pushing the bottle up and back. The Snap-Lock will hold the bottle in a vertical position suspended above the base.
  4. Push down firmly on the carbonating button for around 2 seconds, release, and repeat -- 3 times for light fizz, 5 times for strong fizz, and more for extra strong fizz.
  5. When you've reached the right carbonation level, gently pull the bottle towards you until it reaches its fully forward position and remove.
  6. Enjoy your bubbles!

Questions? Contact us via email or phone at 0800-085-8373,